MAACA.org

I also start stain test...

1 or 2 coat, still don’t know. I was under the impression with more coat, i will mask the burl a little bit, but look like the opposite... i will put some clear to have a better idea.

I start de trickiest part of the veneer... The front where the glass and plastics is made in four section And there is a recess that i have to take care... so i used a template to pre-cut the veneer to have less sanding to do 9D422D58-F8E0-4866-9D96-FF149557E28A.jpeg 1D2B395D-CFD6-4E5A-842E-475ABCA1...

In one place, the veneer put little bit of thickness... i have to sand the new veneer. I made a guide to sand it at the right place

A lot of progress this week... Speaker gone to recone and repair, Chrome send to GG buffing. Powdercoat send to Mr performance New part: speaker grill cloth, cloth wire for the speaker. F24E26F5-6EA4-4D10-8F01-A6B9020056D0.jpeg Receive the new veneer and starting the reveneer process. 5297F32C-541E-...

A batch of brackets un the tumbler, work very well! 36h

Amp repaint! Only have one before pics....

Patch are done! I now have a really nice surface to put the new veneer... that also give me the opportunity to test my new contact ciment in gel.

Need to sand more before i can put the new veneer on, bit the patch goes nicely

One of the pics i like the most... harness after ultrasonic cleaner! the difference is alway awesome!
Keep the good work, very interresting

GG is the best

First patch glue

Do you want a jukebox in a box?

More wood working, need a solid base before i can put the new veneer...

More wood work...

I cut the piece to level the veneer before the finish one

And more wood glue

Mecanism is out!

laisse moi regarder ça se soir

the pivot for the playfeild is stock for that area of pin

Look like i will have to redo the veneer... first the top part was already not original and it’s starting to lift. I was able to completely remove it without dammage. After, i remove all the veneer who lift. I will make some patch with new one before i will reveneer all the jukebox. I also reglue al...

the teardown is start...

paidge wrote: ↑

Fri Jun 12, 2020 8:54 am

Tu dois être bon là-dedans les petites bolts avec ton expérience de lunettes.

Par contre, je trouve que t'as pas les mains propres.......

Anyway, have fun avec ton projet.

Si tu changeais le coil dans ta Fathom, tu aurais peut-être les doigts noir également!

First fabrication...

Need bolt to mount a chrome trim in the front between the glass and the red plastic! Bolt + washer + epoxy and file

Little update... First the juke work, do all his cycle, take record, play and cancel, and do it again and again. The juke was hack to remove the coin mecanism... so no coin mecanism, no slug rejector, no coin box and no magazine switch... (a big challenge to put this back like original) There is a l...

Yep! Never say never... i just purchased an other jukebox for restoration. A Wurlitzer Countertop model 41 from 1940-41 12 selection 78 rpm The smallest wurlitzer jukebox Stay tune for the restoration process 95432BC1-3A60-44E8-9EC1-7078B6890483.jpeg 3AC3D0E5-F0C0-4D79-85FD-12FB6851A3D8.jpeg 9757333...

You can print new coil wrapper if you want, inkocknito have it in his web site http://www.pinballrebel.com/pinball/cards/ Have you try the harness in the dish washer... or in the ultrasonic cleaner... result are awesome, but harness need to be completely detach from the playfeild Nice work, keep the...

C’est vraiment une super amélioration et non un bug pour moi! Merci!!!