Bulletproofing Stern SDU-100-C Solenoid Board
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Bulletproofing Stern SDU-100-C Solenoid Board
Had some time this afternoon, so I took some time to bathe the solenoid board from my Meteor in the fountain of youth.
It takes about an hour to future-proof a Stern solenoid board. This should be the standard of care when bringing a new machine into the shop, although I'll admit I've been neglecting this machine in anticipation of a future overhaul.
Here is the before: The board is in relatively good shape. No burnt diodes, lifted traces, or bodge wires. Let's try to make them unnecessary in the future as well.
First thing that should be done is replace those crusty old electrolytic capacitors. These are original to 1979, and although they haven't failed yet, they're well on their way. Pulling out C23, C24, and C26 reveals on the ESR meter that they're badly out of spec. You don't need a fancy meter to do this procedure. Just trust me and replace these capacitors before they fail. They're definitely on the way.
C24 is a small capacitor to the bottom right of the big heatsink. Stern's early revision boards used an electrolytic, but later changed to a tantalum capacitor. If yours looks like it's in a metal can, swap it, otherwise, ignore it.
It can be a challenge to fit new caps into the board, as modern capacitors are much smaller than the originals. C26 was original an axial package, but that's no longer available. I fit in my replacement by drilling a small hole through the board and soldering directly to the wide trace, but you may wish to run a small wire instead. Once you've fitted new capacitors, it's time to make sure your board still works, and adjust the display voltage. Return it to your machine, reconnect the connectors, screw down the board (important!) and make sure everything is working as it should.
After confirming that everything is working, power down the game. Connect your multimeter's clip leads to TP2 and TP8, range it to DC voltage, and power back up. Your meter may read a couple of hundred DC volts now. With an insulated screwdriver, adjust RT1 until you get 160VDC. This will prolong the life of your plasma displays. Careful prodding around in here: you'll definitely feel it if you come in contact with any live parts in this section.
Next step is to add in some jumpers. Bally/Stern were just starting to learn best engineering practices when designing these boards, and they didn't have modern computers to lay out and optimize their circuit designs. They made several errors that left their boards vulnerable to bad pinning, broken wires, and stray voltages. Both C23 and C26 need better paths to ground, and for some reason the 5V bus generated on the solenoid board needs to go all the way back to the MPU board before coming back to the solenoid board on the same harness. I'm sure in 1979 they thought they had a good reason, but forty years later we know better. Three jumpers need to be added to the board. Here's a photo:
All that remains to be done is a complete replacement of the header connectors. I find it easier to remove the polarizing key pins from the strip before soldering rather than clipping short afterwards. Here's the final product, and hopefully, it will manage another forty years without requiring repair:
There are other changes that can be made as well. The LM323K regulators are obsolete and generate significant heat. There are replacements available that completely replace that whole section. I'll start using them when I run out of my supply of the original component.
It takes about an hour to future-proof a Stern solenoid board. This should be the standard of care when bringing a new machine into the shop, although I'll admit I've been neglecting this machine in anticipation of a future overhaul.
Here is the before: The board is in relatively good shape. No burnt diodes, lifted traces, or bodge wires. Let's try to make them unnecessary in the future as well.
First thing that should be done is replace those crusty old electrolytic capacitors. These are original to 1979, and although they haven't failed yet, they're well on their way. Pulling out C23, C24, and C26 reveals on the ESR meter that they're badly out of spec. You don't need a fancy meter to do this procedure. Just trust me and replace these capacitors before they fail. They're definitely on the way.
C24 is a small capacitor to the bottom right of the big heatsink. Stern's early revision boards used an electrolytic, but later changed to a tantalum capacitor. If yours looks like it's in a metal can, swap it, otherwise, ignore it.
It can be a challenge to fit new caps into the board, as modern capacitors are much smaller than the originals. C26 was original an axial package, but that's no longer available. I fit in my replacement by drilling a small hole through the board and soldering directly to the wide trace, but you may wish to run a small wire instead. Once you've fitted new capacitors, it's time to make sure your board still works, and adjust the display voltage. Return it to your machine, reconnect the connectors, screw down the board (important!) and make sure everything is working as it should.
After confirming that everything is working, power down the game. Connect your multimeter's clip leads to TP2 and TP8, range it to DC voltage, and power back up. Your meter may read a couple of hundred DC volts now. With an insulated screwdriver, adjust RT1 until you get 160VDC. This will prolong the life of your plasma displays. Careful prodding around in here: you'll definitely feel it if you come in contact with any live parts in this section.
Next step is to add in some jumpers. Bally/Stern were just starting to learn best engineering practices when designing these boards, and they didn't have modern computers to lay out and optimize their circuit designs. They made several errors that left their boards vulnerable to bad pinning, broken wires, and stray voltages. Both C23 and C26 need better paths to ground, and for some reason the 5V bus generated on the solenoid board needs to go all the way back to the MPU board before coming back to the solenoid board on the same harness. I'm sure in 1979 they thought they had a good reason, but forty years later we know better. Three jumpers need to be added to the board. Here's a photo:
All that remains to be done is a complete replacement of the header connectors. I find it easier to remove the polarizing key pins from the strip before soldering rather than clipping short afterwards. Here's the final product, and hopefully, it will manage another forty years without requiring repair:
There are other changes that can be made as well. The LM323K regulators are obsolete and generate significant heat. There are replacements available that completely replace that whole section. I'll start using them when I run out of my supply of the original component.
Last edited by semicolin on Sun Jan 05, 2020 9:51 pm, edited 1 time in total.
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
There are lots of different parts that are suitable for repairing these boards, and I'm sure you can find cheaper places than the below links if you spend some time looking. I like to buy quality parts that will last a long time and will be a close a fit to the original as possible. Great Plains Electronics offers kits but they're often out of stock. If they are, here is what I recommend, available as of Jan 2020. This might change over time:
Parts:
C23: Nichicon UVR1E153MRD6 15000µF 25V
C24: Kemet T322B225M020AT 2.2µF 20V (the rounded side of the component is the positive end)
C26: Rubycon 450BXW150MEFC18X45 150µF 450V
.100 header strips: Sullins PREC040SFAN-RC
.156: header strips: Molex 0026481241
Parts:
C23: Nichicon UVR1E153MRD6 15000µF 25V
C24: Kemet T322B225M020AT 2.2µF 20V (the rounded side of the component is the positive end)
C26: Rubycon 450BXW150MEFC18X45 150µF 450V
.100 header strips: Sullins PREC040SFAN-RC
.156: header strips: Molex 0026481241
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
-
- MAACA Super Contributor
- Posts: 585
- Joined: Sun Jun 04, 2017 1:23 am
- Location: Guelph
- Has liked: 82 times
- Been liked: 71 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
All you folks that do this stuff impress the heck out of me....
PINS- Hit The Deck/ Tee'd Off/ Flash Gordon/Bluenote / Stern POTC/ DE Star Wars/ Big Hit/ Algar/Asteroid Annie and the Alians/Slugfest/Batman The Dark Knight/DE The Simpsons/Dirty Harry/T2/ Devils Dare/ World Poker Tour/Swords of Fury/ Lethal Weapon/Ripleys BION/Circa 1933/Striker Xtreme
RIP- Sinbad/ Supersonic
RIP- Sinbad/ Supersonic
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Aw shucks! It's really not that hard once you get the hang of it. A well-lit work bench, a steady hand, and a good soldering station are all you need to get started. Hrm, that gives me an idea for another thread...Guard wrote:All you folks that do this stuff impress the heck out of me....
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- steamfitter
- MAACA Mega Contributor
- Posts: 1266
- Joined: Fri Feb 06, 2015 1:31 pm
- Location: Orleans ( Ottawa )
- Has liked: 75 times
- Been liked: 107 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Great post Colin , i like that you put the part numbers that will make my future order a lot easier .
A post for board electronic parts number would be awesome . The hardest part for me in board repair is finding the right part , i've ordered stuff i'll never use
A post for board electronic parts number would be awesome . The hardest part for me in board repair is finding the right part , i've ordered stuff i'll never use
Pins: Black Hole , Lightning , Future Spa, Pink Panther
Jukebox :1972 Seeburg Olympian sps160 , 1986 seeburg SCD-1
Arcade: hang on , space invaders 412 in 1
Projects : seeburg LPC-1 , Excalibur
http://WWW.pinballowners.com/steamfitter
Jukebox :1972 Seeburg Olympian sps160 , 1986 seeburg SCD-1
Arcade: hang on , space invaders 412 in 1
Projects : seeburg LPC-1 , Excalibur
http://WWW.pinballowners.com/steamfitter
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Ping me any time and I'll tell you what you need. Or post it right here!steamfitter wrote:A post for board electronic parts number would be awesome . The hardest part for me in board repair is finding the right part , i've ordered stuff i'll never use
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- steamfitter
- MAACA Mega Contributor
- Posts: 1266
- Joined: Fri Feb 06, 2015 1:31 pm
- Location: Orleans ( Ottawa )
- Has liked: 75 times
- Been liked: 107 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Thankssemicolin wrote:Ping me any time and I'll tell you what you need. Or post it right here!steamfitter wrote:A post for board electronic parts number would be awesome . The hardest part for me in board repair is finding the right part , i've ordered stuff i'll never use
Pins: Black Hole , Lightning , Future Spa, Pink Panther
Jukebox :1972 Seeburg Olympian sps160 , 1986 seeburg SCD-1
Arcade: hang on , space invaders 412 in 1
Projects : seeburg LPC-1 , Excalibur
http://WWW.pinballowners.com/steamfitter
Jukebox :1972 Seeburg Olympian sps160 , 1986 seeburg SCD-1
Arcade: hang on , space invaders 412 in 1
Projects : seeburg LPC-1 , Excalibur
http://WWW.pinballowners.com/steamfitter
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Bulletproofing Bally/Stern Displays
Bonus bulletproofing: Bally/Stern were notoriously cheap for tolerances when choosing components. Some of the resistors on their display boards that were rated for 1/4W often had to dissipate more heat than that.
When one of these resistors fails, it can take out the board entirely. They're getting harder to find every day, and they aren't cheap either. This rework takes about ten minutes per board and costs about fifty cents.
The first thing that should be done when reworking a machine's displays is to strip out R1,3,5,7,9,11(and R56 on a seven-digit unit). Replace all of them with 100K 1/2W resistors.
When one of these resistors fails, it can take out the board entirely. They're getting harder to find every day, and they aren't cheap either. This rework takes about ten minutes per board and costs about fifty cents.
The first thing that should be done when reworking a machine's displays is to strip out R1,3,5,7,9,11(and R56 on a seven-digit unit). Replace all of them with 100K 1/2W resistors.
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Now I know who to call when I need spare parts.Sparky wrote:Gold.
I have about 40 displays and 12 solenoid drivers on shelves... About time I got to them. LOL
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- sylvain
- MAACA Mega Contributor
- Posts: 3577
- Joined: Thu Nov 19, 2009 7:39 am
- Location: Ottawa, Ontario
- Has liked: 57 times
- Been liked: 59 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Those original 100K 1/4W under-rated resistors on displays burn even faster
if the Solenoid Driver High Voltage Regulator section becomes short
or adjusted too high for a while (e.g. HV outputting > 200+ VDC).
I usually adjust the voltage down to 175VDC to preserve the displays.
This also helps lowering the power dissipated by those resistors.
I agree that 1/2W is the way to go, when replacing those resistors.
-Sylvain.
if the Solenoid Driver High Voltage Regulator section becomes short
or adjusted too high for a while (e.g. HV outputting > 200+ VDC).
I usually adjust the voltage down to 175VDC to preserve the displays.
This also helps lowering the power dissipated by those resistors.
I agree that 1/2W is the way to go, when replacing those resistors.
-Sylvain.
Looking for Bally Star-Jet, The Wiggler, Williams Magic City, Grand Lizard, Swords of Fury, 1986 Pinstar Gamatron, and a few others.
Collecting & repairing electro-mechanical and solid state pinball machines with quality and care for 40+ years already.
Serious and fun hobby, powerful nostalgia !
Collecting & repairing electro-mechanical and solid state pinball machines with quality and care for 40+ years already.
Serious and fun hobby, powerful nostalgia !
- DrDude
- MAACA Super Contributor
- Posts: 532
- Joined: Wed Mar 09, 2016 7:29 pm
- Location: Manotick/Ottawa
- Been liked: 1 time
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
Agreed on all counts, Sylvain: Drop the HV section to 175v ALWAYS. And modern 1/2W resistors are the same size as old-school 1/4W, so they fit just fine.sylvain wrote:Those original 100K 1/4W under-rated resistors on displays burn even faster
if the Solenoid Driver High Voltage Regulator section becomes short
or adjusted too high for a while (e.g. HV outputting > 200+ VDC).
I usually adjust the voltage down to 175VDC to preserve the displays.
This also helps lowering the power dissipated by those resistors.
I agree that 1/2W is the way to go, when replacing those resistors.
Grant Goodes
Stern: Meteor, Lightning, Nineball, Cheetah, Seawitch, Catacomb
Bally: Fathom x 2, Centaur
Gottlieb: Black Hole
Wanted: Balls-a-Poppin, Catacomb slingshot plastics
Lust-worthy: Dragonfist, Solar Fire, Funhouse, Skateball, Capersville
Stern: Meteor, Lightning, Nineball, Cheetah, Seawitch, Catacomb
Bally: Fathom x 2, Centaur
Gottlieb: Black Hole
Wanted: Balls-a-Poppin, Catacomb slingshot plastics
Lust-worthy: Dragonfist, Solar Fire, Funhouse, Skateball, Capersville
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
I bring them down to 160VDC and they're still bright. You should see some of the new Stackpole 1/2w minis! They're even smaller; like a combination of a through-hole and surface mount component. No real reason to use them unless you're trying to save space, but the actual package itself is only 2mm x 6mm. I ordered them by mistake once and they were small enough that I couldn't read the colour code.DrDude wrote:Agreed on all counts, Sylvain: Drop the HV section to 175v ALWAYS. And modern 1/2W resistors are the same size as old-school 1/4W, so they fit just fine.
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8
- djsupermariobros
- MAACA New Contributor
- Posts: 34
- Joined: Sat Sep 17, 2016 8:31 pm
- Location: st louis de gonzague
Re: Bulletproofing Stern SDU-100-C Solenoid Board
How important is the clear plastic protector on the board ??? Its should be better whitout it or not looking for opinion
professional pinbal challenger 3 (power play) memory lane (stern) nugent (stern) mini arcade 412 in1 bartop 619 in 1 gottlieb sky jump now a addict to pinball , gottlieb corral, stern galaxie
- sylvain
- MAACA Mega Contributor
- Posts: 3577
- Joined: Thu Nov 19, 2009 7:39 am
- Location: Ottawa, Ontario
- Has liked: 57 times
- Been liked: 59 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
It is there to protect any tech or owner against possible dangerous or lethal electric shock, in the high-voltage section (over 230V DC at the input).djsupermariobros wrote:How important is the clear plastic protector on the board ??? Its should be better whitout it or not looking for opinion
As the plastic protector does not impede cooling, this original Solenoid Driver plastic cover is _better with it_ in my experience and opinion.
Plus it looks more original too - it can be cleaned with Novus 2 if it is dirty.
-Sylvain.
Looking for Bally Star-Jet, The Wiggler, Williams Magic City, Grand Lizard, Swords of Fury, 1986 Pinstar Gamatron, and a few others.
Collecting & repairing electro-mechanical and solid state pinball machines with quality and care for 40+ years already.
Serious and fun hobby, powerful nostalgia !
Collecting & repairing electro-mechanical and solid state pinball machines with quality and care for 40+ years already.
Serious and fun hobby, powerful nostalgia !
- cdnpinballer
- MAACA Mega Contributor
- Posts: 2725
- Joined: Mon Oct 18, 2010 9:48 am
- Location: Ottawa, Ontario
- Been liked: 3 times
Re: Bulletproofing Stern SDU-100-C Solenoid Board
I had to open up one of my Bally games and decided while I was in there to see how low the voltage can go while still illuminating the displays. 154 volts. I didn’t realize they could go that low!
- semicolin
- MAACA Mega Contributor
- Posts: 1189
- Joined: Sun Apr 17, 2016 4:32 pm
- Location: Ottawa, ON
- Has liked: 172 times
- Been liked: 226 times
- Contact:
Re: Bulletproofing Stern SDU-100-C Solenoid Board
That’s too many! What have I started?
Sharing my space with: Meteor, Tag Team, Dragon, Centaur II, Middle Earth, Xenon, Captain Fantastic, Dolly Parton, Star Trip, Street Fighter cab w/Premium 8